Tag Archives: warning light

Reset service light Toyota Sequoia first generation

Leave a reply

Reset VSC trac warning light Toyota Sequoia first generation. From year: 2005, 2006, 2007.

How to reset VSC trac warning light Toyota Sequoia 1 generation.

This light warns that there is a problem somewhere in the vehicle stability control system and traction control system (two−wheel drive models) or active traction control system (four−wheel drive models). The light will come on when the ignition key is turned to “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as conventional braking operates when applied, there is no problem to continue your driving.

In the following cases, contact your Toyota dealer:

  • The warning light does not come on after the ignition key is turned to “ON”.
  • The warning light remains on after the ignition key is turned to “ON”.
  • The warning light comes on while driving.

    • All information how can you reset VSC trac warning light is taken from Toyota Sequoia owners manual.

    Reset service light Toyota Sequoia first generation

    Leave a reply

    Reset VSC trac warning light Toyota Sequoia first generation. From year: 2005, 2006, 2007.

    How to reset VSC trac warning light Toyota Sequoia 1 generation.

    This light warns that there is a problem somewhere in the vehicle stability control system and traction control system (two−wheel drive models) or active traction control system (four−wheel drive models). The light will come on when the ignition key is turned to “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as conventional braking operates when applied, there is no problem to continue your driving.

    In the following cases, contact your Toyota dealer:

  • The warning light does not come on after the ignition key is turned to “ON”.
  • The warning light remains on after the ignition key is turned to “ON”.
  • The warning light comes on while driving.

    • All information how can you reset VSC trac warning light is taken from Toyota Sequoia owners manual.

    Reset oil service light BMW F10

    Leave a reply

    Reset oil service light BMW F10. From year: 2010, 2011, 2012, 2013.

    How to reset oil service light BMW F10.

    1. Switch ignition to ON position, do not start the engine, push start engine/ignition button without depressing clutch/brake.
    2. Wait for the service  warning light to dissapear.
    3. Immediately after service reminder goes out, push & hold only button on bottom left of tacho /instrument display.
    4. Display will change and show brake pad wear indicator picture.
    5. Push and release same button again to scroll through menu.
    6. When you reach the engine oil warning light push & hold the button until option appears to reset interval.
    7. Push and hold, warning light will reset.
    8. Switch OFF the ignition and then on again to see if warning light has been reset.

     

    General information. The engine oil consumption is dependent on the driving style and driving conditions. Therefore, check the engine oil level after every refueling using the electronic engine oil level check.

    Oil types BMW F10. No oil additives. Oil additives may lead to engine damage. Approved oil types Your service center can advise you on which engine oils have been approved by the manufacturer of your vehicle. The engine oil quality is critical for the life of the
    engine. Only use approved BMW High Performance oil. Approved oils belong to the viscosity grades SAE 0W-40, SAE 0W-30, SAE 5W-40 and SAE 5W-30.

    Reset service light indicator Seat Inca

    Leave a reply

    Reset service light indicator Seat Inca. From year: 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003.

    How to reset service light indicator Seat Inca.

    1. Turn on the ignition, do not start the engine.
    2. Push and holf the left hand button on the clocks.
    3. With the button still pressed turn the ignition to off.
    5. Release the button and you should be able to toggle between the oil, insp1 and insp2 warning light.
    6. Choose the warning light that you want to reset.
    7. On the right hand side of the clocks there are 2 buttons.
    8. Push the bottom button with a biro and hold it until the warning light is reset.

    Reset service light indicator Renault Safrane

    Leave a reply

    Reset service light indicator Renault Safrane. How to reset maintenance light, reset oil service light. Can be made manually by use button on car dash board.

    Reset service light indicator Renault Safrane. It was built in years: 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000.

    1. The reset button is located on the bottom right hand side of the Rev counter on the instrument cluster.
    2. Turn ON the ignition, do not start the vehicle.
    3. Push reset button until Spanner warning light symbol will start flash.
    4. Keep button depressed until Spanner warning light symbol stops flashing and remains illuminated.
    5. Indicator shows appropriate service interval.
    6. Release reset button.
    7. Turn OFF the ignition and then start your Renault Sfrane to see if spanner warning light has been reset.

    Note. Some vehicles are fitted with a SERV lamp, this is not a service interval indicator lamp, it is a malfunction indicator lamp (MIL).