1. Turn the ignition to run (one position before starting engine).
2. Ensure odometer reading is shown, turn ignition off.
3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
4. Hold down knob for at least 5 seconds. The odometer indicates “000000″ and the light goes off. If the system fails to reset, the light will continue flashing.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.
Reset service interval display, insp and oil service for Volvo XC90, 2006, that can be made manually by use button on car dashboard.
Reset service light indicator, engine oil life Volvo XC90, oil reset instructions:
“Resetting the service reminder indicator (SRI), model years 2002-
The service reminder indicator (SRI) informs the driver that it is time for the car to be serviced. The text message is displayed for 120s each time the ignition is switched on.
Proceed as follows to reset the service reminder indicator (SRI):
1.Ignition position I
2. Press and hold in the reset button for the trip odometer
3. Ignition position II. Note! Turn the key to position II within 2 seconds
4. Hold the reset button for the trip meter pressed in until the original value has been reset. Note! For all vehicles from the 2003 model year a general yellow lamp will light when the reset button must be released
5. Release the reset button for the trip odometer within 4 seconds. The instrument gives an audible signal when resetting has succeeded
6. If the trip meter is already reset the reset button should be held in for a minimum of 10 seconds and a maximum of 14 seconds.
Note! If the reset button for the trip odometer is not released within 4 seconds, the service reminder indicator (SRI) is not reset.”
2005-2009
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates for 3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Start the engine and bring up the trip meter A reading.
Vehicles with smart key system:
Turn the “ENGINE START STOP” switch off.
While pressing the Trip Meter reset button, press the “ENGINE START STOP” switch once (do not start engine).
Continue to press and hold the button until the trip meter displays “000000”.
1.Turn the ignition off and then start the engine to verify the indicator has been reset.
Vehicles without smart key system:
2. Turn the ignition switch off.
3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
4. Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Turn the ignition to run (one position before starting engine).
Ensure odometer reading is shown. Turn ignition off.
While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Start the engine and bring up the trip meter A reading.
Vehicles with smart key system:
Turn the “ENGINE START STOP” switch off.
While pressing the Trip Meter reset button, press the “ENGINE START STOP” switch once (do not start engine).
Continue to press and hold the button until the trip meter displays “000000”.
1.Turn the ignition off and then start the engine to verify the indicator has been reset.
Vehicles without smart key system:
2. Turn the ignition switch off.
3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
4. Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.