Category Archives: Service light reset BMW

Oil reset, oil light indicator, maintenance light reset, service light reset, without using a computer for BMW

Reset oil service light BMW 7 Series

Leave a reply

Reset oil service light BMW 7 Series. For models: BMW E32, BMW E38, BMW E65, BMW E66, BMW F01, BMW F02.

Reset oil service light BMW 7 Series model E38. From years: 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001.

How do you reset oil service light BMW 7 Series model E38.

  1. Ignition key must be off.
  2. Press and hold the trip odometer reset button in the instrument cluster (left button), and turn the ignition key to the first position.
  3. Keep the button pressed for approx 5 seconds until one of the following words appear in the display: “Oil Service” with “Reset”.
  4. The service due is shown with “reset” if the coded minimum consumption limit has been reached and resetting is possible. If “reset” is not shown, the minimum limit has not been reached and resetting is not possible.
  5. Press and hold the reset button again until the word “Reset” begins to flash.
  6. While the display is flashing, press the left button briefly to reset the service interval. After the display has shown the new interval the following will appear: “End SIA”.
  7. The system can only be reset again after  2.5 gal (10 liters) of fuel have been consumed.

 

Reset oil service light BMW 7 Series E65. From years: 2002, 2003, 2004, 2005, 2006, 2007, 2008.

How to reset oil service light BMW 7 Series E65.

  1. Insert key.
  2. Press START/STOP button without pressing clutch/brake, wait for the service reminder to disappear.
  3. Immediately, after service reminder goes out, press and hold the odometer reset. After 3 seconds a warning triangle will appear.
  4. .
  5. Keep the odometer reset button pressed. After another 2-3 seconds the oil-can symbol will appear. If you hold the button too long, about 10 seconds, the system will go into an internal coding mode. In this case, shut everything down and start over.
  6. After properly performing step-3, the system will be in the service menu mode. Use the push button (BC button) on the end of the left steering column switch (wipers, high/low beams) to scroll through the various service items.
  7. When the oil service light is displayed, press the BC button on the end of wiper switch. “Reset” should now appear in the display. Press and hold the BC button for 2-3 seconds. A small clock display will show as the reset is being performed.
  8. Reset oil service light BMW 7 Series E65, picture below.
  9. .
  10. You can now select another item to reset (as in step-4) or press the START/STOP button to end.

Reset oil service light BMW 7 Series model E66. From years: 2002, 2003, 2004, 2005, 2006, 2007, 2008.

How do you reset oil service light BMW 7 Series model E66.

  1. Insert key.
  2. Press START/STOP button without pressing clutch/brake, wait for the service reminder to disappear.
  3. Immediately, after service reminder goes out, press and hold the odometer reset. After 3 seconds a warning triangle will appear.
  4. .
  5. Keep the odometer reset button pressed. After another 2-3 seconds the oil-can symbol will appear. If you hold the button too long, about 10 seconds, the system will go into an internal coding mode. In this case, shut everything down and start over.
  6. After properly performing step-3, the system will be in the service menu mode. Use the push button (BC button) on the end of the left steering column switch (wipers, high/low beams) to scroll through the various service items.
  7. When the oil service light is displayed, press the BC button on the end of wiper switch. “Reset” should now appear in the display. Press and hold the BC button for 2-3 seconds. A small clock display will show as the reset is being performed.
  8. Reset oil service light BMW 7 Series E66, picture below.
  9. .
  10. You can now select another item to reset (as in step-4) or press the START/STOP button to end.

 

 

Reset oil service light BMW F10

Leave a reply

Reset oil service light BMW F10. From year: 2010, 2011, 2012, 2013.

How to reset oil service light BMW F10.

  1. Switch ignition to ON position, do not start the engine, push start engine/ignition button without depressing clutch/brake.
  2. Wait for the service  warning light to dissapear.
  3. Immediately after service reminder goes out, push & hold only button on bottom left of tacho /instrument display.
  4. Display will change and show brake pad wear indicator picture.
  5. Push and release same button again to scroll through menu.
  6. When you reach the engine oil warning light push & hold the button until option appears to reset interval.
  7. Push and hold, warning light will reset.
  8. Switch OFF the ignition and then on again to see if warning light has been reset.

 

General information. The engine oil consumption is dependent on the driving style and driving conditions. Therefore, check the engine oil level after every refueling using the electronic engine oil level check.

Oil types BMW F10. No oil additives. Oil additives may lead to engine damage. Approved oil types Your service center can advise you on which engine oils have been approved by the manufacturer of your vehicle. The engine oil quality is critical for the life of the
engine. Only use approved BMW High Performance oil. Approved oils belong to the viscosity grades SAE 0W-40, SAE 0W-30, SAE 5W-40 and SAE 5W-30.

Reset inspection service light indicator BMW E39

Leave a reply

Reset inspection service light indicator BMW E39. From years: 1997, 1998, 1999, 2000, 2001, 2002, 2003.

How do you reset inspection service light indicator BMW E39.

  1. Ignition key must be off.
  2. Press and hold the trip odometer reset button in the instrument cluster (left button), and turn the ignition key to the first position.
  3. Keep the button pressed for approx 5 seconds until one of the following words appear in the display: “Inspection” with “Reset”.
  4. The service due is shown with “reset” if the coded minimum consumption limit has been reached and resetting is possible. If “reset” is not shown, the minimum limit has not been reached and resetting is not possible.
  5. Press and hold the reset button again until the word “Reset” begins to flash.
  6. While the display is flashing, press the left button briefly to reset the service interval. After the display has shown the new interval the following will appear: “End SIA”.
  7. The system can only be reset again after  2.5 gal (10 liters) of fuel have been consumed.

That it is the full procedure how to reset inspection service light indicator BMW E39. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for BMW cars. Or any error which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders when by yourself.

Oil Service Reset BMW Z8

Leave a reply

Reset service light indicator, engine oil life BMW Z8 year 2000-2003 reset instructions:

BMW recommends the use of a reset tool.

Manual Reset

1. Turn off the ignition.
2. Press and hold the TRIP ODOMETER button in the instrument cluster and turn the ignition to Accessory.
3. Keep the button pressed for 5 seconds until OIL SERVICE RESET (RE) or INSPECTION RESET (RE) appears in the display. Then release the button.
4. Press and hold the button again for 5 seconds until RE or RESET flashes in the display. Then release the button.
5. With the display flashing
6. Turn the ignition off and start the engine to verify the indicator has been reset.

Oil Service Reset BMW Z4

Leave a reply

Reset service light indicator, engine oil life BMW Z4 year 2004-2005 reset instructions:

BMW recommends the use of a reset tool.

Manual Reset

1. Turn off the ignition.
2. Press and hold the TRIP ODOMETER button in the instrument cluster and turn the ignition to Accessory.
3. Keep the button pressed for 5 seconds until OIL SERVICE RESET (RE) or INSPECTION RESET (RE) appears in the display. Then release the button.
4. Press and hold the button again for 5 seconds until RE or RESET flashes in the display. Then release the button.
5. With the display flashing
6. Turn the ignition off and start the engine to verify the indicator has been reset.

2006-2012
BMW recommends the use of a reset tool.

Manual Reset

1. Turn ignition to Terminal 15 which is one turn of the key or one press of the START/STOP button.
2. Press and hold the Instrument Cluster Set/Reset button for 10 seconds.
3. The upper display in the Instrument Cluster will be illuminated with a Service Item. The lower display in the Instrument Cluster will indicate the remaining time or mileage left for that Service Item. Pressing the button repeatedly will allow the display to scroll through all of the Condition Based Service Items.
4. Press and hold the Instrument Cluster Set/Reset button again and the lower display screen will indicate “”OK”” or “”DUE””.”
5. Pressing the Instrument Cluster Set/Reset button again will allow the “”RESET”” to appear in the lower window for that service. Releasing and reapplying the button one more time will reset the service displayed in the upper window only. ”
6. Turn the ignition off and start the engine to verify the indicator has been reset.