2006-2010
Turn the ignition to run (one position before starting engine).
Press the INFO and RESET (arrow) buttons on the DIC at the same time to enter the personalization menu.
Press the INFO button to scroll through the menu until OIL LIFE RESET is displayed.
Press and hold the RESET button until the DIC display shows ACKNOWLEDGED. This will tell you the system has been reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007-2010
Turn the ignition to run (one position before starting engine).
Press the INFO and RESET (arrow) buttons on the DIC at the same time to enter the personalization menu.
Press the INFO button to scroll through the menu until OIL LIFE RESET is displayed.
Press and hold the RESET button until the DIC display shows ACKNOWLEDGED. This will tell you the system has been reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
How do you reset maintenance light, reset service light indicator Chevrolet GMC Trucks Terrain. For reset maintenance light and that can be made manually by use button on car dash board.
Reset service light indicator, engine oil life Chevrolet GMC Trucks Terrain, oil reset instructions:
2010
With Driver Information Centre (DIC):
Turn the ignition to run (one position before starting engine).
Press the MENU button until vehicle information menu is displayed then scroll through the menu with the down arrow until Remaining Oil Life is selected then press SET/CLR (check button) to select.
Use up or down arrow to select YES to reset.
Confirm reset by pressing SET/CLR button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Without Driver Information Centre (DIC):
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
If the Change Engine Oil Soon message goes off the system is reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Reset service light indicator, engine oil life Mercedes Benz C-Class, year 1997-2000 reset instructions:
How to reset oil service light Mercedes Benz C-Class. From year: 1997-2000
*Diagnostic Reset Tool Required (please refer to TOOLS page)
Manual Reset:
Turn key in steering lock to position 2.
Within 4 seconds press 0 button twice.
The present status for days or distance displays, within 10 seconds turn the electroninc key in steering lock to position 0.
Press and hold 0 button while turning electronic key in steering loack to position 2 again. The present status for days or distance displays once more. Continue to hold 0 button for approximately 10 seconds until a signal sounds and the display shows 10 000 (15000KM) for approximately 10 seconds.
Release 0 button, the status is reset.
2001
Turn key in steering lock to position 2.
Call up the trip odometer and main odometer: press either of the lower two buttons on the left hand side of steering wheel until the display appears.
Press either of the top buttons on steering wheel (arrows) until the FSS indicator appears.
Press R button on the instrument cluster for 2-4 seconds.
The display reads “DO YOU WANT TO RESET SERVICE INTERVAL?” confirm by pressing R button.
Press and hold the R button on instrument cluster again until signal sounds. Message will res “SERVICE INTERVAL HAS BEEN RESET”.
2002
Switch ignition on.
Repeatedly press the system selection button (bottom button located on left hand side of steering wheel) until the service symbol is displayed in the multifunction display.
Repeatedly press the SCROLL FORWARD/BACK button (top button on left hand side of steering wheel) until the service symbol is displayed in the multifunction display.
“DO YOU WANT TO RESET THE SERVICE INTERVAL?” appears, confirm that you see the message by holding down the RESET (R) button until you hear a signal.
The reset interval is set.
2003
Turn on the ignition (standard display of the control system appears).
Press SYSTEM button on the multifunction steering wheel until FSS indicator with service symbol and the service deadline appear on display.
Message appears on display “DO YOU WANT TO RESET THE SERVICE INTERVAL?” Confirm by pressing RESET (R) button until you hear a signal (approximately 4 seconds).
2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator appears in the display.
Press RESET button for about 3 seconds until this message appears: “SERVICE INTERVAL? RESET WITH R BUTTON FOR 3 SEC.”
To confirm press RESET button until you hear a signal. The service indicator now displays the reset interval.
2006-2008
Turn the ignition to run (one position before starting engine).
Maintenance and tire pressure information will be displayed when the “MAINT” button is pushed on the centre console.
To display the setting of the maintenance interval, select the “Engine Oil” key using the joystick and push the “ENTER” button.
To reset the maintenance interval, select the “Reset” key using the joystick and push the “ENTER” button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Turn the ignition to run (push START/STOP button once).
Switches for the trip computer are located on the right side of the combination meter panel. When the ignition switch is pushed to the ON position press the (square) button to bring up “Setting” and and press (circle) button to select.
Use the (circle) button to scroll to MAINTENANCE and use the (square) button to select.
Select ENGINE OIL to set or reset the distance for changing the oil.
Repeat step 2 to set or reset the distance for the OIL FILTER.
Turn the ignition off and then start the engine to verify the indicator has been reset.