Tag Archives: left

Reset enhanced accident response system Fiat 500

Leave a reply

Reset enhanced accident response system Fiat 500. From year: 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

How to reset enhanced accident response system Fiat 500.

In the event of an impact causing air bag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of theevent, the ORC will determine whether to have the Enhanced Accident Response System perform the following functions:

  • Cut off fuel to the engine.
  • Flash hazard lights as long as the battery has power or until the ignition key is turned off.
  • Turn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed.
  • Unlock the doors automatically.
  • After the event occurs, when the system is active, the message Fuel Cutoff See Handbook is displayed. Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.

System reset procedure.

After an impact causing air bag deployment, the left and right turn signal lights, located in the instrument panel cluster, will both be blinking, until the ignition is turned off. In order to move your vehicle to the side of the road you must follow the system reset procedure.

  1. Turn ignition OFF. Turn signal switch must be placed in neutral state.
  2. Turn ignition ON. Customer will see left turn light is OFF. Right turn light blinks.
  3. Turn right turn signal switch ON. Customer will see – right turn light is ON solid. Left turn light blinks.
  4. Turn left turn signal switch ON. Customer will see, left turn light is ON solid. Right turn light blinks.
  5. Turn right turn signal switch ON. Customer will see, right turn light is ON solid. Left turn light blinks.
  6. Turn left turn signal switch ON. Customer will see, Left turn light is ON solid. Right turn light is ON solid.
  7. Turn left turn signal switch OFF. Turn signal switch must be placed in neutral state. Customer will see, left turn light is OFF. Right turn light is OFF.
  8. Turn ignition OFF. Customer will see, system is now reset and the engine may be started.
  9. Turn hazard flashers OFF (manually).
  10. If a reset procedure step is not completed within 45 seconds, then the turn signal lights will turn off and the reset procedure must be performed again in order to be successful.

If a deployment occurs.

The advanced front Air Bags are designed to deflate immediately after deployment.

Front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system.

If you do have a collision which deploys the air bags, any or all of the following may occur:

  • The nylon air bag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the air bags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately.
  • As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose orthroat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning.

Do not drive your vehicle after the air bags have deployed. If you are involved in another collision, the air bags will not be in place to protect you.

Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retractor assemblies replaced by an authorized dealer immediately. Also, have the Occupant Restraint Controller (ORC) system serviced as well.

Oil reset service light indicator Land Rover Discovery 3

Leave a reply

Reset service light indicator Land Rover Discovery 3. How to reset maintenance light, reset oil service light. Can be made manually by use button on car dash board.

Reset service light indicator Land Rover Discovery 3.

Procedure to check/reset service status, distance counter on a Land Rover Discovery 3.

  1. Switch ignition OFF.
  2. Press and Hold left instrument panel reset button, switch ignition ON to position I (accessories).
  3. Keep reset button pressed for approximately 5 seconds until the LCD displays RESET SIA.
  4. The distance to service (e.g. 2150 miles) and the service type (e.g. Inspection/oil service) will be displayed.
  5. Has the Reset Distance limit been reached or exceeded? o NO.
  6. Follow instructions in section 2 below o YES Follow Reset Distance Counter instructions below Reset Distance counter procedure.
  7. Press and hold left instrument reset button for 5 seconds. RESET will begin to flash on the LCD display.
  8. To reset distance the left hand button should be pressed before the RESET message has flashed 5 times. The LCD will display END SIA. Switch ignition off.

Procedure to check/reset service status date counter on a Land Rover Discovery 3.

  1. Press left instrument panel reset button once.
  2. The LCD will display RESET SIA followed by the service due date.
  3. Has the Reset Date limit been reached or exceeded? o NO.
  4. Press the left instrument button once.
  5. The LCD will display END SIA to indicate the service interval check/reset procedure has been cancelled. o YES, Follow Reset Date Counter instructions below Reset Date counter procedure.
  6. Press and hold left instrument reset button for 5 seconds.
  7. RESET will begin to flash on the LCD display.
  8. To reset distance the left hand button should be pressed before the RESET message has flashed 5 times.
  9. The LCD will display END SIA. Switch ignition off.

oil-reset-service-light-indicator-Land-Rover-Discovery-3

Reset washer fluid low message Saab 9-3

Leave a reply

How to reset washer fluid low message Saab 9-3 first generation.

Reset washer fluid low message Saab 9-3 first generation. From year: 1998, 1999, 2000, 2001, 2002.

  1. Switch ignition to ON position, one position befor you start the engine.
  2. The brake light failure warning light cannot be removed by pressing CLEAR button.
  3. To reset the message push the brake pedal to clear.

All information how to reset washer fluid low message on a Saab 9-3 it’s taken from Saab 9-3 owners manual.
Washer Saab 9-3. The reservoir holds 5 quarts (4.7 litres). When the SID message “WASHER FLUID LEVEL LOW” appears there is about 1.5 quarter (1.4 litres) left. Fill with quality washer fluid and follow the instructions on the package to reduce the risk of freezing. If the reservoir is run dry and the car has a rear-window wiper, then after refilling you cannot wash the rear window until you have first washed the windscreen.

Oil reset service light indicator Mercedes E320

Leave a reply

How do you reset maintenance light, reset service light indicator Mercedes E320. For reset maintenance light and that can be made manually by use button on car dashboard.

Reset service light indicator, engine oil life Mercedes E320, oil reset instructions:

  1. Turn the ignition switch to “On” without starting the engine.
  2. Press and release the “0” button on the left side of the instrument cluster twice immediately after turning the ignition on.
  3. Turn the ignition off.
  4. Press and hold the “0” button.
  5. Turn the ignition on.
  6. Release the “0” button after the service message resets. Turn the ignition off.

 

Reset service light indicator BMW 7 Series

Leave a reply

Reset oil service light BMW 7 Series. For models: BMW E32, BMW E38, BMW E65, BMW E66, BMW F01, BMW F02.

Reset oil service light BMW 7 Series model E38. From years: 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001.

How do you reset oil service light BMW 7 Series model E38.

  1. Ignition key must be off.
  2. Press and hold the trip odometer reset button in the instrument cluster (left button), and turn the ignition key to the first position.
  3. Keep the button pressed for approx 5 seconds until one of the following words appear in the display: “Oil Service” with “Reset”.
  4. The service due is shown with “reset” if the coded minimum consumption limit has been reached and resetting is possible. If “reset” is not shown, the minimum limit has not been reached and resetting is not possible.
  5. Press and hold the reset button again until the word “Reset” begins to flash.
  6. While the display is flashing, press the left button briefly to reset the service interval. After the display has shown the new interval the following will appear: “End SIA”.
  7. The system can only be reset again after  2.5 gal (10 liters) of fuel have been consumed.

 

Reset oil service light BMW 7 Series E65. From years: 2002, 2003, 2004, 2005, 2006, 2007, 2008.

How to reset oil service light BMW 7 Series E65.

  1. Insert key.
  2. Press START/STOP button without pressing clutch/brake, wait for the service reminder to disappear.
  3. Immediately, after service reminder goes out, press and hold the odometer reset. After 3 seconds a warning triangle will appear.
  4. Reset service light indicator BMW 7 Series

    .

  5. Keep the odometer reset button pressed. After another 2-3 seconds the oil-can symbol will appear. If you hold the button too long, about 10 seconds, the system will go into an internal coding mode. In this case, shut everything down and start over.
  6. After properly performing step-3, the system will be in the service menu mode. Use the push button (BC button) on the end of the left steering column switch (wipers, high/low beams) to scroll through the various service items.
  7. When the oil service light is displayed, press the BC button on the end of wiper switch. “Reset” should now appear in the display. Press and hold the BC button for 2-3 seconds. A small clock display will show as the reset is being performed.
  8. Reset oil service light BMW 7 Series E65, picture below.
  9. Reset service light indicator BMW 7 Series.
  10. You can now select another item to reset (as in step-4) or press the START/STOP button to end.

Reset oil service light BMW 7 Series model E66. From years: 2002, 2003, 2004, 2005, 2006, 2007, 2008.

How do you reset oil service light BMW 7 Series model E66.

  1. Insert key.
  2. Press START/STOP button without pressing clutch/brake, wait for the service reminder to disappear.
  3. Immediately, after service reminder goes out, press and hold the odometer reset. After 3 seconds a warning triangle will appear.
  4. Reset oil service.
  5. Keep the odometer reset button pressed. After another 2-3 seconds the oil-can symbol will appear. If you hold the button too long, about 10 seconds, the system will go into an internal coding mode. In this case, shut everything down and start over.
  6. After properly performing step-3, the system will be in the service menu mode. Use the push button (BC button) on the end of the left steering column switch (wipers, high/low beams) to scroll through the various service items.
  7. When the oil service light is displayed, press the BC button on the end of wiper switch. “Reset” should now appear in the display. Press and hold the BC button for 2-3 seconds. A small clock display will show as the reset is being performed.
  8. Reset oil service light BMW 7 Series E66, picture below.
  9. Reset oil service.
  10. You can now select another item to reset (as in step-4) or press the START/STOP button to end.