Tag Archives: indicator

Oil service reset Ford Trucks Expedition

Leave a reply

How do you reset maintenance light, reset service light indicator Ford Trucks Expedition. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life Ford Trucks Expedition, oil reset instructions:

2007-2009

Turn the ignition to run (one position before starting engine).
Press and release the RESET stem to display “OIL LIFE = XXX% HOLD RESET = NEW”.
Press and hold the RESET stem for 2 seconds and release. Oil life is set to XX% and “OIL LIFE SET TO XX%” is displayed.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2010
Turn the ignition to run (one position before starting engine).
Press and release SETUP to display “OIL LIFE XXX% HOLD RESET = NEW”.
Press and hold RESET for 2 seconds and release to reset the oil life to 100%.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Ford Trucks E-Series

Leave a reply

How do you reset maintenance light, reset service light indicator Ford Trucks E-Series. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life Ford Trucks E-Series, oil reset instructions:

2009-2010

Turn the ignition to run (one position before starting engine).
Press and release the SELECT/RESET stem to display “OIL LIFE = XXX% HOLD RESET = NEW”.
Press and hold the SELECT/RESET stem for 2 seconds and release. Oil life is set to XX% and “OIL LIFE SET TO XX%” is displayed.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Land Rover LR2

Leave a reply

2006-2010

Press and hold the trip reset button with the vehicle stationary and in a power mode less than 6 (two positions before starting engine).
While holding the trip reset button, enter the vehicle into power mode 6 (one position before starting engine).
Release the trip reset button within 10 seconds of entering power mode If the manual reset mode has been successfully entered ‘dISt’ or ‘DATE’ will be displayed in the odometer, depending on which trigger has been activated.
To clear the ‘dISt’ trigger press, and hold the trip reset button for more than 5 seconds within 10 seconds of entering the manual re-set mode. If successful, ‘RESET’ will be displayed in the odometer for 5 seconds. If the date trigger has not been activated ‘END’ will then be displayed in the odometer.
If the date trigger has been activated, ‘DATE’ will be displayed in the odometer. To clear the trigger press and hold the trip reset button for more than 5 seconds within 10 seconds of ‘DATE’ being displayed. If successful, ‘RESET’ will be displayed within the odometer for 5 seconds followed by ‘END’ The odometer will now exit re-set mode.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Toyota Venza

Leave a reply

2009-2010
Start the engine and bring up the trip meter A reading.
Vehicles with smart key system:
Turn the “ENGINE START STOP” switch off.
While pressing the Trip Meter reset button, press the “ENGINE START STOP” switch once (do not start engine).
Continue to press and hold the button until the trip meter displays “000000”.

1.Turn the ignition off and then start the engine to verify the indicator has been reset.
Vehicles without smart key system:
2. Turn the ignition switch off.
3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
4. Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Toyota Highlander

Leave a reply

How to reset oil service light Toyota Highlander. From year: 2005-2008

Turn the ignition to run (one position before starting engine).
Ensure odometer reading is shown. Turn ignition off.
While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Vehicles without smart key system:
Turn the ignition to run (one position before starting engine).
Ensure Trip Metre A reading is shown. Turn the ignition off.
Vehicles with smart key system:
Press the “ENGINE START STOP” switch once (do not start engine).
Ensure Trip Metre A reading is shown. Turn the ignition off.
While pressing the Trip Meter reset button, press the “ENGINE START STOP” switch once (do not start engine).
Without multi-information display: Continue to press and hold the button until the trip meter displays ě000000î.
With multi-information display: Continue to press and hold the button until “COMPLETE” appears on the multi-information display.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Hybrid
Press the “POWER” switch once (do not start engine).
Turn off the hybrid system with the trip meter A reading shown.
Ensure Trip Metre A reading is shown. Turn the ignition off.
While holding down the trip meter reset knob the ěPOWERî switch must be set in ON mode (do not start engine). A message ěCOMPLETE” will appear on the multi information display.
Turn the ignition off and then start the engine to verify the indicator has been reset.