Category Archives: Service light reset Toyota

Oil reset, oil light indicator, maintenance light reset, service light reset, without using a computer for Toyota

Reset malfunction indicator lamp Toyota Tundra second generation

Leave a reply

How to reset malfunction indicator lamp Toyota Tundra 2 generation.

Reset malfunction indicator lamp Toyota Tundra second generation. From year: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

This lamp comes on when the ignition key is turned to the “ON” position and goes off after the engine starts. This means that the warning light system is operating properly. If the lamp remains on, or the lamp comes on while driving, first check the followings.

Empty fuel tank. If the fuel tank is empty, refuel immediately.
Loose fuel tank cap. If the fuel tank cap is loose, securely tighten it.
These cases are temporary malfunctions. The malfunction indicator lamp will go off after taking several driving trips. If the lamp does not go off even after several trips, contact your Toyota dealer as soon as possible.

If the fuel tank is not empty or the fuel tank cap is not loose.

There is a problem somewhere in the engine, emission control system, electronic throttle control system, automatic transmission electrical system or warning light system itself.

Contact your Toyota dealer as soon as possible to service the vehicle. If engine speed does not increase when the accelerator pedal is depressed, there may be a problem somewhere in the electronic throttle control system. At this time, vibration may occur. However, if you depress the accelerator pedal more firmly and slowly, you can drive your vehicle at low speeds. Have your vehicle checked by your Toyota dealer as soon as possible. Even if the abnormality of the electronic throttle control system is corrected during low speed driving, the system may not be recovered until the engine is stopped and the ignition key is turned to “ACC” or “LOCK” position.

Be especially careful to prevent erroneous pedal operation.

Emissions Inspection and Maintenance (I/M) programs.

Your vehicle may not pass a state emission inspection if the malfunction indicator lamp remains on. Contact your Toyota dealer to check your vehicle’s emission control system and OBD (On−Board Diagnostics) system before taking your vehicle for the inspection.

All information how can you reset malfunction indicator lamp is taken from Toyota Tundra second generation owners manual.

Reset seat belt reminder light Toyota Tundra second generation

Leave a reply

How to reset seat belt reminder light Toyota Tundra 2 generation.
Reset seat belt reminder light Toyota Tundra second generation. From year: 2005-2014.

Driver’s Seat Belt Reminder Light and Buzzer.

The light and buzzer act as a reminder to buckle up the driver’s seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes and buzzer sounds if the driver’s seat belt is not fastened. Unless the driver fastens the belt, the light continues flashing and the buzzer stops after about 4 to 8 seconds.

Front Passenger’s Seat Belt Reminder Light.

The light acts as a reminder to have the front passenger buckle up the seat belt. Once the ignition key is turned to “ON”, the reminder light flashes if a passenger sits in the front passenger seat and does not fasten the seat belt. If luggage or other load is placed on the front passenger seat, depending on its weight, the reminder light may come on.

All information how can you reset seat belt reminder light is taken from Toyota Tundra second generation owners manual.

That it is the full procedure how to reset seat belt reminder light Toyota Tundra second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

This is an information site where you can solve your car problems. Send us a comment if our procedures are correctly. If you would have anything to add, for us every opinion counts.

Reset oil service light indicator Toyota Tundra second generation

Leave a reply

Reset oil service light indicator, engine oil life Toyota Tundra 2. From year: 2005-2014 reset instructions:

How to reset oil service light Toyota Tundra 2 generation.

This light acts as a reminder when to replace the engine oil. This light will come on when the ignition key is turned to “ON” and will go off after about a few seconds. When you drive for about 7200 km (4500 miles) after the engine oil replacement, this light illuminates for about 3 seconds and then flashes for about 12 seconds with the ignition key turned to the “ON” position. If you continue driving without replacing the engine oil, and if the distance driven exceeds 8000 km (5000 miles), the light will come on after the ignition key is turned to “ON” position. The light will remain on thereafter. If the light is flashing, we recommend that you replace the engine oil at an early opportunity depending on the driving and road conditions. If the light comes on, replace it as soon as possible.

The system must be reset after the engine oil replacement. Reset the system by the following procedure:

When tje Maint Requd appears on a Toyota Tundra you must follow this steps to reset the warning light.

1. Turn the ignition key to the “ACC” or “LOCK” position with the odometer reading shown.
2. Turn the ignition key to the “ON” position while holding down the trip meter reset knob. See below pictures.
3. On dash will appear ” – – – – – – ” who will blink.
4. Hold down the knob for at least 5 seconds. The odometer indicates “000000” and the light goes off.
5. If the system fails to reset, the light will continue flashing.

All information how can you reset oil service light is taken from Toyota Tundra second generation owners manual.

Reset open door warning light Toyota Tacoma second generation

Leave a reply

How to reset open door warning light Toyota Tacoma 2 generation.

Reset open door warning light Toyota Tacoma second generation. From year: 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

This light remains on until all the doors are completely closed.

To reset open door on a Toyota Tacoma you must close all dors, make sure that thei are relly close. If the open door warning light is still on after you have checked that they are close, you can have a problem with the sensor that indicate this.

That it is the full procedure how to reset open door warning light Toyota Tacoma second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.

This is an information site where you can solve your car problems. Send us a comment if our procedures are correctly. If you would have anything to add, for us every opinion counts.

Reset SRS airbag warning light Toyota Tacoma second generation

Leave a reply

How to reset SRS airbag warning light Toyota Tacoma 2 generation.

Reset SRS airbag warning light Toyota Tacoma second generation. From year: 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014.

This light will come on when the ignition key is turned to the “ON” position. After about 6 seconds, the light will go off. This means the systems of the airbag and front seat belt pretensioners are operating properly.

This warning light system monitors the airbag sensor assembly, front airbag sensors, side and curtain shield airbag sensors, curtain shield airbag sensors, driver’s seat position sensor, driver’s seat belt buckle switch, front passenger occupant classification system, passenger airbag off switch, passenger airbag on−off indicator light, seat belt pretensioner assemblies, inflators, “RSCA OFF” indicator light, interconnecting wiring and power sources.

The front passenger occupant classification system includes the front passenger occupant classification ECU, pressure sensor, load sensor, front passenger’s seat belt buckle switch, front passenger’s seat position sensor and belt tension sensor.

If either of the following conditions occurs, this indicates a malfunction somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle.

  • The light does not come on when the ignition key is turned to the “ON” position or remains on for more than 6 seconds.
  • The light comes on while driving.

All information how can you reset SRS airbag warning light is taken from Toyota Tacoma second generation owners manual.

That it is the full procedure how to reset SRS airbag warning light Toyota Tacoma second generation. If you like to reset any maintenance oil light after an oil change. Or reset check engine light, airbag light, inspection key or insp errors when maint reqd, for Toyota cars. Or any warning light for service reminder which appears on the display. Write in the search box the car name for which you want to find information, and find how to reset other service reminders by yourself.