Category Archives: Service light reset Toyota

Oil reset, oil light indicator, maintenance light reset, service light reset, without using a computer for Toyota

Maintenance Oil Light Reset Toyota Highlander 2013

Leave a reply

How do you reset maintenance light, reset service light indicator Toyota Highlander, year 2012, 2013, 2014. For reset maintenance light and that can be made manually by use button on car dash board.

Reset service light indicator, engine oil life Toyota Highlander, oil reset instructions:

Vehicles without smart key system

  1. Turn the ignition to run (one position before starting engine).
  2. Ensure Trip Metre A reading is shown. Turn the ignition off. (Go to step 3)

Vehicles with smart key system

  1. Press the “ENGINE START STOP” switch once (do not start engine).
  2. Ensure Trip Metre A reading is shown. Turn the ignition off.
  3. While pressing the Trip Meter reset button, press the “ENGINE START STOP” switch once (do not start engine).
    Without multi-information display: Continue to press and hold the button until the trip meter displays “000000”.
    With multi-information display: Continue to press and hold the button until “COMPLETE” appears on the multi-information display.
  4. Turn the ignition off and then start the engine to verify the indicator has been reset.

Reset low engine oil pressure warning light Toyota Prius XW20

Leave a reply

Reset low engine oil pressure warning light Toyota Prius second generation XW20. From year: 2003, 2004, 2005, 2006, 2007, 2008.

How to reset low engine oil pressure warning light Toyota Prius second generation XW20.

Low Engine Oil Pressure Warning Light.

This light warns that the engine oil pressure is too low. If it stays on while you are driving, pull off the road to a safe place and stop the engine immediately. Call a Toyota dealer or qualified repair shop for assistance. The light may come on when the oil level is extremely low. It is not designed to indicate low oil level, and the oil level must be checked using the level dipstick.

All information how to reset low engine oil pressure warning light is taken from Toyota Prius 2 XW20 owners manual.

Reset tire pressure warning light Toyota Rav4 XA40

Leave a reply

Reset tire pressure warning light Toyota Rav4 XA40 fourth generation. From year: 2013, 2014.

How to reset oil service light Toyota Rav4, 3 generation XA30, 4 generation.

How to initialize the tire pressure warning system.

  1. Park the vehicle in a safe place and turn the engine switch to the “LOCK” position (vehicles without a smart key system) or off (vehicles with a smart key system). Initialization cannot be performed while the vehicle is moving.
  2. Adjust the tire inflation pressure to the specified cold tire inflation pressure level. Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level.
  3. Turn the engine switch to the “ON” position (vehicles without a smart key system) or IGNITION ON mode (vehicles with a smart key system).
  4. Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly 3 times.
  5. Reset-tire-pressure-warning-light-Toyota-Rav4-XA40
  6. Vehicles without a smart key system: Wait for a few minutes with the engine switch in the “ON” position and then turn the engine switch to the “ACC” or “LOCK” position. Vehicles with a smart key system: Wait for a few minutes with the engine switch in IGNITION ON mode and then turn the engine switch off.

Registering ID codes Toyota Rav 4.

The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code. Have the ID code registered by your Toyota dealer.

When to replace your vehicle’s tires. Tires should be replaced if:

  • You have tire damage such as cuts, splits, cracks deep enough to expose the fabric, and bulges indicating internal damage.
  • A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage.

If you are not sure, consult with your Toyota dealer.

Replacing tires and wheels (vehicles with the tire pressure warning system).

If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. After driving for about 20 minutes, the tire pressure warning light blinks for 1 minute and stays on to indicate a system malfunction.

Tire life Toyota Rav4.

Any tire over 6 years old must be checked by a qualified technician even if it has seldom or never been used or damage is not obvious.

Routine tire inflation pressure checks (vehicles with the tire pressure warning system).

The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks.

Situations in which the tire pressure warning system may not operate properly (if equipped).

In the following cases, the tire pressure warning system may not operate properly.

  • If non-genuine Toyota wheels are used.
  • A tire has been replaced with a tire that is not an OE (Original Equipment) tire.
  • A tire has been replaced with a tire that is not of the specified size.
  • Tire chains etc. are equipped.
  • Lock nuts are equipped.
  • An auxiliary-supported run-flat tire is equipped.
  • If a window tint that affects the radio wave signals is installed.
  • If there is a lot of snow or ice on the vehicle, particularly around the wheels or wheel housings.
  • If the tire inflation pressure is extremely higher than the specified level.
  • If the spare tire is in a location subject to poor radio wave signal reception.
  • If a large metallic object which can interfere with signal reception is put in

*: Vehicles with a full-size spare tire only

Performance may be affected in the following situations.

  • Near a TV tower, electric power plant, gas station, radio station, large display, airport or other facility that generates strong radio waves or electrical noise.
  • When carrying a portable radio, cellular phone, cordless phone or other wireless communication device.

When the vehicle is parked, the time taken for the warning to start or go off could be extended.
When tire inflation pressure declines rapidly for example when a tire has burst, the warning may not function.

Reset oil service light Toyota Rav4 XA30

Leave a reply

Reset oil service light Toyota Rav4, third generation XA30. From year: 2009, 2010, 2011, 2012, 2013.

How to reset oil service light Toyota Rav4, 3 generation XA30.
To reset the oil change system, follow the procedure below:
Vehicles without smart key system.
  1. Turn the engine switch off with the trip meter A reading shown.
  2. While pressing the trip meter reset button, turn the engine switch to the “ON” position.
  3. Press and hold the button until the trip meter displays “000000”.

 

Vehicles with smart key system.
  1. Turn the “ENGINE START STOP” switch off with the trip meter A reading shown.
  2. While pressing the trip meter reset button, turn the “ENGINE START STOP” switch to IGNITION ON mode.
  3. Press and hold the button until the trip meter displays “000000”.
All information how to reset oil service light is taken from Toyota Rav 4 owners manual.
Used engine oil. Used engine oil contains potentially harmful contaminants which may cause skin disorders such as inflammation or skin cancer, so care should be taken to avoid prolonged and repeated contact. To remove used engine oil from your skin, wash thoroughly with soap and water.
Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.
Do not leave used engine oil within the reach of children.
 Reset-oil-service-light-Toyota-Rav4-XA30
.
Vehicles without smart key system.
  • The following gauges, meters and displays illuminate when the engine switch is in the “ON” position.
Vehicles with smart key system.
  • The following gauges, meters and displays illuminate when the “ENGINE START STOP” switch is in IGNITION ON mode.
  • Tachometer. Displays the engine speed in revolutions per minute.
  • Speedometer. Displays the vehicle speed.
  • Engine coolant temperature gauge. Displays the engine coolant temperature.
  • Fuel gauge. Displays the quantity of fuel remaining in the tank.
  • Trip information display.
  • Automatic transmission shift position indicator lights.
  • Odometer/trip meter.
  • Odometer. Displays the total distance the vehicle has been driven.
  • Trip meter. Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances independently.
  • Odometer/trip meter switching and trip meter resetting button. Switches between odometer and trip meter displays. Pushing and holding the button will reset the trip meter when the trip meter is being displayed.

Reset service light Toyota Sequoia first generation

Leave a reply

Reset VSC trac warning light Toyota Sequoia first generation. From year: 2005, 2006, 2007.

How to reset VSC trac warning light Toyota Sequoia 1 generation.

This light warns that there is a problem somewhere in the vehicle stability control system and traction control system (two−wheel drive models) or active traction control system (four−wheel drive models). The light will come on when the ignition key is turned to “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as conventional braking operates when applied, there is no problem to continue your driving.

In the following cases, contact your Toyota dealer:

  • The warning light does not come on after the ignition key is turned to “ON”.
  • The warning light remains on after the ignition key is turned to “ON”.
  • The warning light comes on while driving.

    • All information how can you reset VSC trac warning light is taken from Toyota Sequoia owners manual.